裝配圖懲罰函數法二級圓柱齒輪減速器的優化設計

裝配圖懲罰函數法二級圓柱齒輪減速器的優化設計,裝配,懲罰,函數,二級,圓柱齒輪,減速器,優化,設計 懲罰函數法二級圓柱齒輪減速器的優化設計學生姓名：江崇文 班級：0781052指導老師：朱保利摘要：減速器是各類機械設備中廣泛使用的傳動裝置。其主要特點為傳遞功率大、制造簡單、維修方便和使用壽命長等優點。傳統的減速器設計一般通過反復的試湊、校核確定設計方案，雖然也能獲得滿足給定條件的設計方案，實踐證明，按照傳統設計方法作出的設計方案，大部分都有改進的余地，不是最佳方案。本文將對二級圓柱齒輪減速器進行優化設計?？紤]到以中心距最小為目標，在此采用了懲罰函數法。通過設計變量的選取、目標函數和約束條件的確定，建立了圓柱齒輪減速器設計的數學模型。編寫了優化設計程序，通過在計算機上運行和計算，得出優化設計各參數的大小。從理論上對圓柱齒輪減速器的結構進行了分析并作了常規設計，并對其它的一些附件進行了相應的設計，設計完畢，對其齒面、齒根彎曲強度進行校核，結果滿足要求。結果表明，采用優化設計方法后，在滿足強度要求的前提下，減速器的尺寸大大降低了，減少了用材及成本，提高了設計效率和質量。關鍵詞：圓柱齒輪減速器 優化設計 懲罰函數法 中心距 常規設計指導老師簽名：Penalty function Optimal Design for Two-Grade Helical Cylindrical Gear RedactorStudent name：Jiang Chong Wen Class：0781052Supervisor：Zhu Bao LiAbstract：Reducer is a transmission device which is widely found in mechanical equipment. The main characteristics of it is large power transmission、manufacture simple、easy maintenance and long life. Traditionally, in order to get satisfied design data of reducer, you must cut and try again and again. Although this design can satisfy conditions given. Proved by the practice, according to the traditional design method to the design, most of them have room for improvement, it is not optimal. In this article we will two-grade helical cylindrical gear redactor conduct optimal design . Taking account the minimum distance of center into the goal, penalty function used in this method . In this paper, by the way of selecting design variable , setting up goal function and restriction condition , the mathematical model of cylindrical gear reducer is established . The preparation of the optimal design program , run by the computer and calculating the optimal design parameters . The structure of the gear reducer is analyzed and made conventional design in theory, and some other accessories for the corresponding design , which proved reasonable for the the checking of Tooth surface and tooth root bending strength after the designation completed . The results show that the optimal design methods , strength requirements are met under the premise of the size reducer greatly reduced, reducing the timber and the cost , improve the design efficiency and quality. Key words: Helical Cylindrical Gear Redactor optimal design penalty function Center distance Conventional DesignSignature of supervisor: