基于plc的物流分揀系統設計

基于plc的物流分揀系統設計,基于,plc,物流,分揀,系統,設計 基于plc的物流分揀系統設計摘 要 利用可編程控制器(PLC),設計成本低、效率高的材料自動分揀裝置.以PLC為主控制器,結合氣動裝置、傳感技術、位置控制等技術,運用梯形圖編程，實現對鐵塊及不同顏色材料的自動分揀。系統具有自動化程度高、運行穩定、精度高、易控制的特點,可根據不同對象,稍加修改本系統即可實現要求. 本設計采用的是三菱系列的可編程控制器（PLC）。第一章進行了設計的分析。第二章根據對設計的分析進行了方案的確定和PLC型號的選用，同時進行了IO接點的分配。第三章進行了電氣原理圖的設計同時對按鈕等電器元件進行了選用，第四章進行了PLC程序的設計和操作過程的敘述。關鍵詞：可編程控制器，分揀裝置，控制系統，傳感器。 The Design of Material Selecting System By PLC ControlledABSTRACT The design of an automatic sorting with low cost and high efficiency is presented in the paper，which regards programmable logic controller(PLC) as the master controller and combines pneumatic device，sensing technology，position control and other technology to implement automatic selecting of the products live.Program with the ladder-shape figure,designing the automatic system that sorts out iron,aluminum and plastic and different colour.The device is characteristic of high automation, steady running, high precision and easy control, which can fulfill the requirement according to different situations with little modifications.This design adoption is the programmable controller(PLC) of Mitsubishi series.Chapter 1 carried on the analysis of design.Chapter 2 according to carrying on a project really and settling with PLC to the analysis of design the choice of the model number, carried on the allotment of IO point of contact in the meantime.Chapter 3 carried on the design of electricity principle diagram to wait an electric appliances component to carry on choice towards pressing button in the meantime, chapter 4 carried on PLC the design of the procedure and the description of the operation process.KEY WORDS: programmable logic controller，sorting device，control system，sensors目 錄前 言1第1章多種材料分揀裝置系統設計分析21.1設計對象介紹31.1.1 課題任務提出31.1.2控制方案選擇4第2章 材料分揀系統方案分析52.1 用戶I/O設備及所需PLC的I/O點數52.2 用戶存儲容量的選擇62.3 PLC型號的選擇6第3章 材料自動分揀裝置系統的硬件設計83.1 自動分揀裝置系統的設計過程83.1.1 自動分揀系統動作順序分析83.3.2設計要求83.1.3 保護要求93.2電氣元件的選擇93.2.1 按鈕的選用93.2.2 傳感器的選用93.2.3 電機的選用103.2.4 變頻器的選用103.3 PLCI/O點實際接線圖143.3.1 PLC的接線143.3.2 PLC的I/0接線圖15第4章 PLC程序設計174.1系統的順序功能圖設計174.1.1 系統的順序功能圖如下圖4-1所示：184.2 梯形圖程序設計204.2.1黃燈及其閃爍控制部分204.2.2紅燈禁止下料控制部分224.2.3蜂鳴器控制程序234.2.3傳送帶材料計數控制程序244.2.4其他主要程序設計25第5章 調試與抗干擾系統分析265.1 程序的模擬調試265.2程序的現場調試265.3 系統調試275.3.1 調試過程275.3.2 調試結果275.4 PLC的抗干擾系統285.4.1電磁干擾源及對系統的干擾285.4.2 PLC控制系統中電磁干擾的主要來源285.4.3 PLC控制系統工程應用的抗干擾設計305.4.4主要抗干擾措施30結 論32謝 辭33參考文獻34附錄35外文資料翻譯47