購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
編號
無錫太湖學院
畢業設計（論文）
相關資料
題目： 皮套圈座多軸鉆孔專機設計
信機 系 機械工程及自動化專業
學 號： 0923176
學生姓名： 孫文華
指導教師： 尤麗華 （職稱：副教授 ）
（職稱： ）
2013年5月25日
目 錄
一、畢業設計（論文）開題報告
二、畢業設計（論文）外文資料翻譯及原文
三、學生“畢業論文（論文）計劃、進度、檢查及落實表”
四、實習鑒定表
無錫太湖學院
畢業設計（論文）
開題報告
題目： 皮套圈座多軸鉆孔專機設計
信機 系 機械工程及自動化 專業
學 號： 0923176
學生姓名： 孫文華
指導教師： 尤麗華 （職稱：副教授 ）
（職稱： ）
2012年11月14日
課題來源
無錫市江泰機械制造廠是一家專業從事外協件加工的企業，公司現采用加工中心加工紡織機械零件--皮圈架座上的三個孔,皮套圈座是紡織機械上一個異形件,加工精度高,用普通機床加工較困難，工裝時間長，加工成本高，效率不高。因而需要設計一臺專機達到提高工作效率，降低成本。
科學依據（包括課題的科學意義；國內外研究概況、水平和發展趨勢；應用前景等）
普通機床加工零件時，不僅工人勞動強度很大，效率也不高，而且不利于保證產品加工精度。專用機床是按高度工序集中原則設計的，即在一臺機床上可以同時完成許多同一種工序或多種不同工序的加工，它可以同時用多個刀具進行切削，機床的輔助動作實現了自動化，結構比普通機床簡單，提高了生產效率。
專用機床與普通機床比較，具有以下特點：
⑴專用機床上的通用部件和標準零件約占全部機床零、部件總量的70%到80%，因此設計和制造的周期短、投資少、經濟效益好。
⑵由于專用機床采用多刀加工，并且自動化程度高，因而比普通機床生產率高，產品質量穩定，勞動強度底。
⑶專用機床的通用部件是經過周密的設計和長期生產實踐考驗的，又有專門廠家成批制造，因此結構穩定，工作可靠，使用和維修方便。
⑷專用機床易于聯成專用機床自動線，以適應大規模的生產需要。
隨著社會經濟的發展，機械制造業也愈來愈受到人們的關注。在皮套圈座方面，生產效率不僅嚴重地威脅著企業的經濟情況，而且大量的工作危害著生產者的健康,立式多軸鉆孔專機有效的緩解了這一現象。鉆孔的要求越高,工人的工作量也就越大,針對手工鉆孔的技術要求也就越高,工人保持長期的精力積中,容易出現生產安全事故,危害性較大.針對這一情況,各個企業采用了不同的方案,包括使用單一的鉆床來減輕勞動者的疲勞度 ,這些措施在一定改善員工的作業要求,但還不能滿足要求。因此,研究合適的皮套圈座立式多軸鉆孔專機,降低了工作強度,特別是減緩工人的精力過度集中,對于防止企業的生產事故有明顯的效果和保護作業人員的生命安全有十分重要的意義。
多軸鉆孔最早出現在日本地區，后經臺灣傳入大陸。距今已有二十年的歷史。
隨著國家不斷的加大對外開放,經濟受到了劇烈的競爭,生產效率成為各個公司緩解壓力的關鍵點,皮套圈座多軸鉆孔專機面臨著更廣闊的應用空間。
研究內容
皮套圈座多軸鉆孔專機的工作原理,結構組成,以及工作特點,控制系統;了解該系統機構的制造工藝,控制系統,安全裝置的工作原理。
在前幾年,手動鉆孔機應用在我國較為廣泛,隨著競爭的不斷加劇,機械加工精度要求不斷地提高,手工鉆孔逐漸被淘汰.單軸鉆孔專機的出現越來越頻繁,世界的一體化不斷加劇,多軸鉆孔專機取代了單軸鉆孔專機受到越來越廣的應用.隨著多軸鉆孔的興起,多軸鉆孔專機大體上分為兩大類,可調式和固定式
多軸鉆床按其加工件的硬度來劃分，可分為中切削型、重切削型和強力超重切削型三類。中切削適用于鋁、鎂、銅等HB≤150以下的工件。重切削適用于孔數大于10個的軟質件或7孔以下的鋼、鐵等HB≤265以下的工件。強力超重切削型試用于265≤HB≤330鋼、鐵等強硬度工件。
總之，綜合考慮各種情況，得出一個最優設計方案，設計一個符合實際情況的皮套圈座立式多軸鉆孔專機。
擬采取的研究方法、技術路線、實驗方案及可行性分析
通過對多軸鉆孔專機的實物研究和要加工產品的市場研究和產品分析,總結得出皮套圈座多軸鉆孔專機的基本結構,工作方式與原理.然后根據考察的結果,再查閱相關書籍,確定基本的設計參數,進行初步的三維建模。交由指導老師檢查,修改.完成后,再對主要載荷部件進行校核.最后出主要零件的零件圖,編寫設計說明書。
可行性分析：《我國多軸鉆床行業2010年發展報告》指出2010年多軸鉆床行業總產值上年增長20%，出口合同額比上年增長15%。目前，國內已有眾多廠家在進行皮套圈座多軸鉆孔專機等相關產品的生產研發工作，如無錫市，數家公司完成對此的研發，并成功用于產品的加工.由此可見，該設計方案切實可行。
研究計劃及預期成果
研究計劃:
2002年10月12日-2002年12月25日：按照任務書要求查閱論文相關參考資料。
2013年3月8日-2013年3月14日：按照要求修改畢業設計開題報告。
2013年3月15日-2013年3月21日：學習并翻譯一篇與畢業設計相關的英文材料。
2013年4月12日-2013年4月25日：機床設計。
2013年4月26日-2013年5月21日：畢業論文撰寫和修改工作。
預期成果：
此多軸鉆孔專機的研究成功可以有效的降低工作強度,主要體現在下面幾個方面:
(1)科學鉆孔,降低對員工的技術要求。
(2)提高效率,增加經濟效益.。
今年來我國生產事故不斷，造成重大人民生命財產的損失，其中很多就是由于長時間的精力高度集中引起的。
特色或創新之處
近年來我國皮套圈座多軸鉆孔專機有了較大的發展。動力系統,傳動系統,鉆孔的質量和技術水平都有較大的提高。特別在孔的精度上，達到了更高的水平。在其它方面均有較大的突破。
我設計的皮套圈座多軸鉆孔專機的特色也在于此，即注重實用性和經濟性；效率高；同時性價比高，成本低。
已具備的條件和尚需解決的問題
已具備的條件：設計過程中所需要的各種軟硬件資源和相關產品實物照片。
尚需解決的問題：相關文獻資料的缺乏，對一些結構設計部分的具體設計指導，以及三維軟件的高級運用技巧。
指導教師意見
指導教師簽名：
年 月 日
教研室（學科組、研究所）意見
教研室主任簽名：
年 月 日
系意見
主管領導簽名：
年 月 日
英文原文
Small-hole drilling in engineering plastics sheet and its accuracy estimation
Hiroki Endo and Etsuo Marui
Abstract
In recent manufacturing processes, the small diameter hole drilling process is frequently used owing to its good characteristics. The drilling process can easily be adapted to wide variations in lot size, processing accuracy, processing spot patterns where holes are made, and so on. Many machine elements, which have small diameter holes, are manufactured using engineering plastics of superior material and machining properties. However, it is not easy to drill holes with a diameter smaller than 1?mm, in recent machining technology as well. In this report, 1-mm diameter holes are drilled on two engineering plastics sheets and their drilling accuracy is discussed.
Keywords: Small diameter hole; Drilling; Engineering plastics; Machining accuracy
1. Introduction
Processing of small diameter holes is done in various materials, corresponding to the trend of downsizing or high accuracy in parts incorporated into electronic equipments, medical instruments or textile machineries. Many techniques are put to practical use, including drilling, ultrasonic machining, electric discharge machining, electrolytic machining, laser beam machining, electron beam machining, fluid or abrasive jet machining, and chemical blanking. Depending on the workpiece material, the machining accuracy, and the lot size, the best process for making holes of small diameter may be appropriately selected. Within these various machining processes, the drilling process can readily deal with a wide variety of machining conditions.
However, there are some difficult problems in drilling holes smaller than 1?mm in diameter. For example, a large load cannot be put on small drills, owing to their low strength and rigidity. Thus, the feed rate per unit drill rotation must be set small. The removal of drilled chips is difficult owing to the small drill flute area.
In many cases, engineering plastics are used in making various machine parts because they are light and have superior specific strength (that is, the ratio of tensile strength to density) compared with carbon steel. Also, the material cost of engineering plastics is competitive and their machinability is fairly good.
With these points as background, the orthogonal cutting of engineering plastics was investigated [1] and it was suggested here that the visco–elastic properties of engineering plastics have some effects on the magnitude of cutting force and the surface roughness of machined surfaces. There is a review paper [2] regarding the machining of engineering plastics. In this review paper, drilling process was also treated. It was pointed out that the heating up of the workpiece due to build-up of swarf on drill flutes is an obstacle to the drilling process of engineering plastics. Recently, some experiments have been attempted on drilling glass–fiber-reinforced engineering plastics sheets [3] and [4], and the thrust force and torque during drilling have been measured. In these papers, it was reported that the delamination phenomenon decreases the drilled hole integrity, when holes of about 5-mm diameter are drilled. However, the investigation on the accuracy in small hole drilling of engineering plastics is left pending.
Then in this paper, small diameter holes of 1?mm are drilled in two typical engineering plastics sheets, and the effect of spindle speed and feed rate on the accuracy (radius error) is estimated.
2. Workpiece materials
Two typical engineering plastics sheets, polyacetal (POM) and polyetherimide (PEI), were drilled. The materials properties are listed in Table 1.
Table 1.
Material properties of workpiece engineering plastics
Performance
Unit
POM
PEI
Specific gravity
1.41
1.27
Rate of water
%
0.22
0.25
Melting point
°C
165
210
Coefficient of linear thermal expansion
cm/cm/°C
9×10?5
5.6×10?5
Tensile strength
MPa
61
124
Tensile extension (Yielding point)
%
40
23
Bending strength
MPa
89
157
Bending elasticity
GPa
2.60
3.07
Compressive strength
MPa
103
118
Izote impact value
J/m
74
42
Rockwell hardness
M scale
119
127
Polyacetal is a crystallized engineering plastics material. The main raw materials are acetal co-polymer and homo-polymer. POM has good fatigue properties and machinability. Many cams, guides and liners are made of POM. Very high accuracy is needed in these machined parts. PEI is an amorphous engineering plastic having superior thermal resistance characteristics. Special electrical parts, for example, electric insulators, connectors, are made of PEI, which is superior in mechanical strength but inferior in machinability to POM.
The workpiece size was: length 100?mm, width 50?mm and thickness 0.8?mm.
3. Experimental apparatus and procedure
The drilling machine used is for small diameter holes, and is equipped with an automatic feed mechanism. A high-frequency induction motor positioned at the uppermost position of the main spindle drives the spindle. Maximum spindle speed is 12,500?rpm. The net spindle speed of the spindle during the drilling is measured by a tachometer, which counts number of the laser beam reflected from a reflective tape pasted on the scroll chuck.
A servomotor for drill feed drives the feed motion of the spindle. The feed is stepless, and a dial gauge equipped at the spindle head measures the length of the drill motion in the spindle axis direction. A stopwatch was used to measure the time needed for this length. The ratio of the moved length to the time is the substantial feed rate per unit time.
The spindle speed was varied between 1250 and 12,500?rpm. And also the feed rate per unit time was varied between 0.405 and 1.986?mm/s. Spindle speed was varied in keeping with the feed rate per unit time. Hence, the feed rate per unit drill rotation became small with the increase in the spindle speed of the drill.
The drill spindle end is attached to the scroll chuck. The drill used here is a conventional twist drill made of high-speed steel with a diameter of 1?mm. In some extra experiments, a 0.3?mm-diameter drill was also used. Such drills have no surface treatment. A dial gauge estimates deflection accuracy of the drill on the scroll chuck during rotation. Extreme care was taken so that the drill deflection was smaller than 5?μm.
The same drill made five holes under the cutting condition of the same spindle speed and the same feed rate. Another drill was used in the drilling under another cutting condition. Of course, the size accuracy of these drills exists within the above-mentioned size scattering. Any evidence of the wear of drills and the build-up of swarf on drill flutes were not recognized after five holes drilling.
Formerly mentioned workpiece of engineering plastics were set on the base of the drilling machine by clamping bolts. Dry cutting without fluid was performed.
4. Calculation of drilled hole shapes
The 1-mm diameter holes drilled on engineering plastics sheets by the process described above are not geometrically true circles, but have a small radial deviation. Shape accuracy of the drilled holes is estimated by the following process.
An optical microscope equipped with digital measuring device measures the shape of the drilled hole. The cross wire of the microscope is set at the circumference of the hole. Then, the coordinates (x,y) of the hole circumference are read. Dividing the circumference into 18 equal parts, the same measurements are then repeated on each spot on the circumference. Using these 18 sets of measured qualities, the equation of the circle that fits closely to the drilled hole is calculated. This is called a least square circle, and in the calculation, the least squares method is applied.
The equation of the least square circle is assumed as follows:
x2+y2+Ax+By+C=0 (1)
Owing to the shape error of the hole, the right hand side of Eq. (1) does not become zero when the above-mentioned measured qualities (xi,yi) are substituted. The residual in this case is vi and the following equation is obtained:
(2)
Here, the coefficients A, B, C in Eq. (1) are determined as the sum of the squared values of the residual vi becomes minimum. Values of these coefficients are obtained by solving the following simultaneous linear equations. In the calculation, N=18.
(3)
Moreover, the coordinates (x0,y0) of the center of the least square circle and its radius rm are obtained as follows:
Corresponding to the above process, the least square circles are described. An example is shown in Fig. 1, where the workpiece material is PEI, drill diameter: 1?mm, spindle speed: 12,500?rpm, and feed rate: 0.405?mm/s. The least square circle is indicated by the broken line.
5. Estimation of machining accuracy and experimental results
Machining accuracy of the drilled holes is estimated by the radius error obtainable from the least square circles. The calculation process of the radius error is given here.
Radius ri at the each measuring spot (xi,yi) is obtained from the coordinate of the least square circle center (x0,y0) of Eqs. (4) and (5) as follows:
(7)
Then, the radius error is calculated by the following equation. The parameter rm in the equation is the radius of the least square circle given by Eq. (6).
Δri=ri?rm (8)
And the position of that measuring spot on the circle is represented by the following angle θi.
(9)
The relation between Δri and θi obtained from the above method is shown in Fig. 2 as a radius error curve. The drilling conditions in this figure are the same as those of Fig. 1 Three concavities and convexities are recognized on the circumference. Then, the drilled hole shape is approximately triangular. Similar results were obtained in other workpiece materials for other drilling conditions. Furthermore, it is seen that the circumference of the drilled hole exists in the vicinity within ±0.02?mm from the least square circle. This drilled hole shape is similar to that produced by the so-called drill walking phenomenon [5]. The radius of the least square circle is slightly larger than that of the drill. The difference between them is about 10?μm.
Result of Fig. 2 is obtained in the measurement at the drill entrance into workpiece. Small burr was formed at the drill exist and the accuracy measurement could not carry out as it is. Then, the burr was forcibly removed and the accuracy was measured. Almost the same accuracy was confirmed, because the workpiece is thin (0.8?mm thickness).
These radius errors are rearranged as functions of the spindle speed or the feed rate for every workpiece material. The results are given in Fig. 3, Fig. 4, Fig. 5 and Fig. 6. Error bars indicate the distribution range of the experimental data. The radius error becomes small hyperbolically with the increase in the feed rate and becomes large linearly with the spindle speed. Small diameter drills were used in this experiment and their bending rigidity is low. Rotational cutting speed is almost zero near the chisel point. At that point, the drill has only a small axial velocity corresponding to the drill feed motion. Accordingly, the rate of penetration [6] is extremely small when the feed rate is small. As mentioned above, the walking phenomenon occurs owing to small errors in drill size. This phenomenon is compounded with the effect of small rate of penetration when small feed rate and large spindle speed are applied. Hence, the positioning accuracy of the drill point against the workpiece is not very good at small feed rate and large
spindle speed. As a result, it is supposed that the radius error becomes large. For example, the rate of penetration, that is the feed rate per unit drill rotation, is about 2?μm when the drill rotation speed is 12,500?rpm and the feed rate is 0.405?mm/s. The rate of penetration is about 100?μm when the drill spindle speed is smallest (1250?rpm) and the feed rate is largest (1.986?mm/s).
One reason for the radius error worsening when the rotation speed becomes high is that chatter [6] related to the drill dynamic characteristics is possible. However, the small drill size errors and the relative drop in the feed rate per unit drill rotation corresponding to the spindle speed increase have a large effect on the radius error. In conclusion, it is important to drill a small hole in the drilling condition so as to maintain a sufficiently high feed rate per unit drill rotation.
An example of superposition of the results of POM and PEI is given in Fig. 7. It is recognized in this figure that the radius accuracy in the drilling of PEI is slightly inferior to that of POM. PEI is a kind of supper engineering plastics. PEI is superior to POM in tensile strength, compressive strength, bending strength, bending elasticity and Rockwell hardness, as seen in Table 1. Owing to this, the machinability of PEI may be worse than that of POM and the result of Fig. 7 regarding the radius error was be obtained.
6. Concluding remarks
Small holes were drilled in two engineering plastics sheets POM and PEI using a drill 1?mm in diameter. Drilling can be done on both workpiece materials.
Reading the drilled hole shape by optical micrometer, and calculating the least square circle, the drilling accuracy (radius error) can be estimated. The radius error becomes worse when the drill feed rate is small and the spindle speed is large. The feed rate per unit drill rotation is relatively small when the spindle speed is large. Hence, it is supposed that the positioning accuracy of the drill against the workpiece is not good, and that the radius error becomes worse under the drilling conditions in which the feed rate per unit drill rotation is small. From this fact, it is desirable that small diameter holes be drilled in the condition in which the feed rate does not become low.
References
[1] K.Q. Xiao and L.C. Zhang, The role of viscous deformation in the machining of polymers, International Journal of Mechanical Science 44 (2002), pp. 2317–2336.
[2] M. Alauddin, I.A. El Baradie and M.S.J. Hashmi, Plastics and their machining: a review, Journal of Materials Processing Technology 54 (1995), pp. 40–60.
[3] W.-C. Chen, Some experimental investigations in the drilling of carbon fiber-reinforced plastic (CFRP) composite laminates, International Journal of Machine Tools and Manufacture 37 (1997), pp. 1097–110.
[4] E. Capello, Workpiece damping and its effect on delamination damage in drilling thin composite laminates, Journal of Materials Processing Technology 148 (2004), pp. 186–195.
[5] M. Tsueda, Y. Hasegawa and H. Kimura, On walking phenomenon of drill, Transactions of the JSME 27 (1961), pp. 816–823.
[6] D.F. Galloway, Some experiments on the influence of various factors on drill performance, Transactions of the ASME 79 (1957), pp. 191–231.
中文譯文
小孔鉆在工程塑料片材方面及其精度估算
摘要
在最近的制造流程中，小直徑鉆孔由于其良好的特性經常被使用。鉆孔工藝能夠輕易的適用于大部分尺寸，加工精度，加工點孔，等等。許多有小直徑孔的機械零件，是使用優質金屬材料和機器特性制造出來的。然而，在最近的加工技術中，鉆一個直徑小于1 毫米的孔也是不容易的。在這份報告中，直徑為1毫米的孔在兩個工程塑料板材的鉆孔和鉆孔的精度進行了討論。
關鍵詞：小直徑孔；鉆孔；工程塑料；加工精度
1.簡介
在各種材料中都存在小直徑孔的加工，根據數據趨勢或從電子設備中反映零件部分的高精度，醫療器械、紡織機械。許多技術投入實際使用，包括鉆孔，超聲加工，電火花加工，電解加工，激光束加工，電子束加工，液體或磨料噴射加工，化學消隱。根據工件材料，加工精度，和尺寸的大小，可以選擇小直徑鉆孔的最佳工藝。在這些不同的加工工藝中，鉆孔工藝可以很容易地處理大部分的加工情況。
但是，鉆孔直徑小于1毫米時有一些困難的問題。例如，一個大的負載不能放在小鉆頭上，由于其較低的強度和剛度。因此，每單位鉆孔旋轉進給速度必須設置小。由于其小的鉆孔區域，鉆屑的去除是一個困難的問題。
在許多情況下，與碳鋼相比工程塑料被使用用于制造各種機械零件（即，拉伸強度與密度的比值）是因?yàn)樗麄冚p和具有較高的強度。同時，工程塑料材料成本擁有競爭性，其加工性能較好。
以這些問題為背景，研究了工程塑料的正交切削[ 1 ]和建議在工程塑料的彈性性質–切削力的大小和加工表面的表面粗糙度的影響。有一份關于工程塑料加工的審查報告[2]。在這篇綜述報告中，鉆孔過程也被關注。指出出對于工程塑料鉆孔由于鉆孔過程中的切屑的累計而導致的材料過熱。最近，一些實驗已經嘗試在鉆孔中使用玻璃纖維來增強塑料片材[ 3 ]，鉆孔過程中的軸向力和扭矩進行了測量。在這些論文中，當孔直徑約5毫米，分層現象會減少鉆孔的完整性。但是，在工程塑料小鉆孔精度調查尚未解決。
在這個報告中，1?毫米的小直徑孔在兩個典型的工程塑料板材的鉆孔，主軸轉速和進給速度對精度的影響（半徑誤差）估計。
2.工程材料
在兩個典型的工程塑料聚甲醛（POM）和聚醚酰亞胺（PEI）。材料特性列于表1。
表1
工程塑料加工件的材料特性
性能
單位
POM
PEI
比重
1.41
1.27
水率
%
0.22
0.25
熔點
°C
165
210
線性熱膨脹
cm/cm/°C
9×10?5
5.6×10?5
拉伸強度
MPa
61
124
拉伸（屈服點）
%
40
23
彎曲強度
MPa
89
157
彎曲彈性模量
GPa
2.60
3.07
抗壓強度
MPa
103
118
絲蘭沖擊值
J/m
74
42
羅克韋爾硬度
M scale
119
127
聚甲醛是一種明確的工程塑料材料。主要原料是縮醛共聚物和均聚物。聚甲醛具有良好的疲勞性能和加工性能。許多凸輪，導板和線路是聚甲醛制成的。非常高的精度是在這些加工零件所需要的。PEI是具有優良的熱特性的無定形工程塑料。特殊的電氣部件，例如，絕緣子，連接器，是由PEI制成的，它在較好的機械強度而機械加工性能不如POM優越。
工件尺寸為：長100?毫米，寬50毫米，厚0.8毫米??。
3.試驗設