動態扭矩與靜態殘余扭矩ppt課件
《動態扭矩與靜態殘余扭矩ppt課件》由會員分享,可在線閱讀,更多相關《動態扭矩與靜態殘余扭矩ppt課件(35頁珍藏版)》請?jiān)谘b配圖網上搜索。
動態扭矩與靜態殘余扭矩,1,一個世紀的創新 Desoutter – A Century of Innovation,CVI3,2014年的主要產品 Main new products 2014,E-LIT,新的辦公大樓 The new headquater in Nantes,Auto screwfeeder,1914年Desoutter工廠 Desoutter plant in 1914,2,2,我們關注的行業 The main focused segments,3,汽車工業 Motor Vehicle Industry,航空航天 Aero plane & Aerospace,輕工裝配 Light Assembly,通用工業 General Industry,3,不同的階段的扭矩值torque in different process,生產過程中in manufacture process,下線檢測offline test,4,不同的階段的扭矩值torque in different process,生產過程中in manufacture process,下線檢測offline test,35 Nm OK,30 Nm,≠,5,生產過程中——?jiǎng)討B(tài)扭矩Dynamic torque,動態扭矩(Dynamic torque): 動態扭矩是指緊固件在被緊固過程中測量得到的峰值,一般來說,是由動力工具施加得到動態扭矩,動態扭矩是在擰緊過程中測量的。動態扭矩產生的對于螺栓的軸向預緊力滿足工程上對預緊力的要求。 Dynamic torque , measured as the peak torque during the tightening fasteners, in general, is obtained by applying a power tool dynamic torque, dynamic torque is measured during tightening. Dynamic torque generated by the axial preload bolt preload to meet the engineering requirements.,,有加速度產生accelerations,6,下線/線上檢測——靜態扭矩Static torque,靜態扭矩(Static torque): 一個緊固件被緊固好之后,將其在擰緊方向上繼續旋轉的瞬間所需要的扭矩。靜態扭矩是在緊固之后測量的。 Static torque, measured after the fastener is tightened, is equal to the torque when fastener continues to rotate in the direction of tightening needed. Static torque is measured after tightening. 檢測扭矩(Audit torque): 靜態扭矩標準時用來監控生產過程的穩定性,因此又稱為檢測扭矩。 Static torque standard used to monitor the stability of the production process, so-called audit torque.,沒有加速度產生No accelerations,7,動態扭矩和靜態扭矩Dynamic torque and static torque,動態力矩 Dynamic torque,殘余力矩 static torque,表面間的摩擦系數,螺紋副的摩擦系數,工件材料、幾何形狀、連接特性,涂層,涂表面處理,支撐件的粗糙度,材料松弛,螺栓硬度、批次,人、機、料,8,動態扭矩和靜態扭矩Dynamic torque and static torque,生產過程中in manufacture process,下線檢測offline test,哪個扭矩值更重要? Which one is important?,重要!,重要!,9,動態扭矩和靜態扭矩Dynamic torque and static torque,動態力矩—生產過程中的扭矩 可以監控、反應擰緊裝配過程的狀態、結果以及工藝能力,,√,10,動態扭矩和靜態扭矩Dynamic torque and static torque,殘余扭矩—檢測扭矩 擰緊裝配完成后,相對穩定的螺栓連接狀態,,√,11,這樣一個現象One phenomena,35Nm,30Nm?,,一段時間后Later,12,這樣一個現象One phenomena,35Nm,40Nm?,,一段時間后Later,13,ISO5393 定義連接的硬度Joint definition,硬連接 α 720,扭矩,100%,螺栓開始受力,30,720,,,α, 角度,,,,,,,,,,,硬,軟,0,5%,達到目標扭矩,,,,,14,硬鏈接Hard Joint,40Nm?,,一段時間后Later,35Nm,,,15,軟鏈接Soft Joint,30Nm,,一段時間后Later,35Nm,,T (Nm),時間,,,,,,,扭矩衰減,16,動態扭矩和靜態扭矩Dynamic torque and static torque,VDI——德國工程師協會 VDI2230、VDI2862(汽車行業擰緊應用)、VDI2647 (動態力矩檢測) VDI2230高強度螺栓連接的系統計算:螺栓的扭矩彈性回彈,動態扭矩和靜態扭矩的比值范圍會較大,比如0.85-1.3,17,,當動靜態扭矩不一致的時候如何評判? 制定動靜態扭矩的對比表 當動靜態扭矩超出比值后/比值不穩定,如何分析? 通過魚骨圖逐項分析 有哪些裝配過程中的誤區,導致動靜態扭矩不一致?,18,制定動靜態扭矩的對比表setup coefficient of dynamic torque and static torque,19,制定動靜態扭矩的對比表setup coefficient of dynamic torque and static torque,動態力矩 dynamic torque,靜態殘余力矩 static torque,軟連接——扭矩衰減,理想狀況—少數的連接,硬連接,,20,動態力矩與殘余力矩—需要關注以下情況 Focus on following issues,靜態力矩離散,靜態力矩過小,,動態力矩 dynamic torque,靜態殘余力矩 static torque,21,當靜態扭矩異常時如何診斷? How to diagnose when static torque abnormal,,,裝配過程 Assembly process,動態扭矩結果,裝配工藝,工具/設備,操作者,擰緊速度,擰緊策略,,材料—連接 Parts and joint,幾何/連接特性,螺栓是否同一批次,工件材料一致性,,裝配順序,,2,1,靜態力矩離散,靜態力矩過小,?,22,靜態力矩過小的常見原因 the reason of static torque is too low,靜態力矩過小,,扭矩衰減 torque attenuation,23,哪些因素導致扭矩衰減main reasons cause torque attenuation,被裝配件的表面粗糙度:材料的變形--局部嵌入 The roughness of the surface of parts 彈性連接材料:尤其是塑料或密封件 elastic joint parts: such as plastic and rubber washer 過快的裝配速度、不合理的裝配動作 unreasonable assembly speed and sequence 其他:如裝配過程中的溫度 other reason: temperature,24,哪些因素導致扭矩衰減main reasons cause torque attenuation,被裝配件的表面粗糙度:材料的變形--局部嵌入 The roughness of the surface of parts 彈性連接材料:尤其是塑料或密封件 elastic joint parts: such as plastic and rubber washer 過快的裝配速度、不合理的裝配動作 unreasonable assembly speed and sequence 其他:如裝配過程中的溫度 other reason: temperature,25,26,哪些因素導致扭矩衰減main reasons cause torque attenuation,被裝配件的表面粗糙度:材料的變形--局部嵌入 The roughness of the surface of parts 彈性連接材料:尤其是塑料或密封件 elastic joint parts: such as plastic and rubber washer 過快的裝配速度、不合理的裝配動作 unreasonable assembly speed and sequence 其他:如裝配過程中的溫度 other reason: temperature,盡量避免部件的表面粗糙度過大 avoid too high friction,,27,哪些因素導致扭矩衰減main reasons cause torque attenuation,被裝配件的表面粗糙度:材料的變形--局部嵌入 The roughness of the surface of parts 彈性連接材料:尤其是塑料或密封件 elastic joint parts: such as plastic and rubber washer 過快的裝配速度、不合理的裝配動作 unreasonable assembly speed and sequence 其他:如裝配過程中的溫度 other reason: temperature,盡量避免部件的彈性過大 avoid high elastic part,,28,哪些因素導致扭矩衰減main reasons cause torque attenuation,被裝配件的表面粗糙度:材料的變形--局部嵌入 The roughness of the surface of parts 彈性連接材料:尤其是塑料或密封件 elastic joint parts: such as plastic and rubber washer 過快的裝配速度、不合理的裝配動作 unreasonable assembly speed and sequence 其他:如裝配過程中的溫度 other reason: temperature,,降低最終擰緊的速度 reduce tightening speed 分步擰緊—如分步驟設置目標扭矩60%--80%--100% Multiple steps tightening 使用擰緊(如至目標扭矩80%)+反松+最終擰緊的方法 use reverse and multiple steps tightening,29,被裝配件的表面粗糙度:材料的變形--局部嵌入 The roughness of the surface of parts 彈性連接材料:尤其是塑料或密封件 elastic joint parts: such as plastic and rubber washer 過快的裝配速度、不合理的裝配動作 unreasonable assembly speed and sequence 其他:如裝配過程中的溫度 other reason: temperature,哪些因素導致扭矩衰減main reasons cause torque attenuation,,,,,,,,殘余扭矩減小、夾緊力未達到,最終扭矩: 100%,30,被裝配件的表面粗糙度:材料的變形--局部嵌入 The roughness of the surface of parts 彈性連接材料:尤其是塑料或密封件 elastic joint parts: such as plastic and rubber washer 過快的裝配速度、不合理的裝配動作 unreasonable assembly speed and sequence 其他:如裝配過程中的溫度 other reason: temperature,哪些因素導致扭矩衰減main reasons cause torque attenuation,選用合適的工具 use right tool 多軸同步擰緊 multiple spindle fastening 擰緊的次序 right assembly sequence,,31,哪些因素導致扭矩衰減main reasons cause torque attenuation,被裝配件的表面粗糙度:材料的變形--局部嵌入 The roughness of the surface of parts 彈性連接材料:尤其是塑料或密封件 elastic joint parts: such as plastic and rubber washer 過快的裝配速度、不合理的裝配動作 unreasonable assembly speed and sequence 其他:如裝配過程中的溫度 other reason: temperature,避免不合理的摩擦 avoid unreasonable friction 避免熱膨脹系數不同/相差過大 avoid too high difference of coefficient of thermal expansion,,32,動態扭矩和靜態扭矩Dynamic torque and static torque,有沒有公式? Any formula,33, Info.desoutter-china@ Tel: 021-24165100 Fax: 021-24165202 上海市松江區新橋鎮莘磚公路518號37號樓,聯系方式 How to Find Desoutter,34,More Than Productivity,35,- 1.請仔細閱讀文檔,確保文檔完整性,對于不預覽、不比對內容而直接下載帶來的問題本站不予受理。
- 2.下載的文檔,不會出現我們的網址水印。
- 3、該文檔所得收入(下載+內容+預覽)歸上傳者、原創作者;如果您是本文檔原作者,請點此認領!既往收益都?xì)w您。
下載文檔到電腦,查找使用更方便
30 積分
下載 |
- 配套講稿:
如PPT文件的首頁顯示word圖標,表示該P(yáng)PT已包含配套word講稿。雙擊word圖標可打開word文檔。
- 特殊限制:
部分文檔作品中含有的國旗、國徽等圖片,僅作為作品整體效果示例展示,禁止商用。設計者僅對作品中獨創性部分享有著作權。
- 關 鍵 詞:
- 動態 扭矩 靜態 殘余 ppt 課件
鏈接地址:http://italysoccerbets.com/p-2694692.html