外文翻譯發動機拉缸問題探討

《外文翻譯發動機拉缸問題探討》由會員分享，可在線閱讀，更多相關《外文翻譯發動機拉缸問題探討（17頁珍藏版）》請在裝配圖網上搜索。

1、畢業設計(論文)外文資料翻譯學院 (系)： 機械工程學院 專 業： 機械制造及自動化 姓 名： 學 號： (用外文寫)外文出處： Discussion Pull Cylinder Engine 附 件： 1.外文資料翻譯譯文；2.外文原文。 指導教師評語：此翻譯文章簡述發動機拉缸的機理，分析造成發動機拉缸的原因，并提出了防止拉缸的措施。翻譯用詞比較準確，文筆也較為通順，為在以后工作中接觸英文資料打下了基礎 簽名： 年 月 日注：請將該封面與附件裝訂成冊。附件1：外文資料翻譯譯文發動機拉缸問題探討摘要 簡述發動機拉缸的機理，分析造成發動機拉缸的原因，并提出了防止拉缸的措施。關鍵詞 發動機 拉缸

2、預防措施發動機在工作過程中常常遇到發動機拉缸現象，所謂拉缸，就是發動機的活塞環或活塞與缸套的工作表面出現拉傷、拉毛、拉成溝槽的現象。拉缸具有相當?shù)奈：Γ讜r缸套的的磨損率很高，最高可達正常的幾百倍，使活塞、活塞環及缸套的壽命大為降低，使活塞與缸套咬死，造成發動機損壞。因此，掌握拉缸形成的機理，認真分析造成拉缸的原因，研究預防措施，對避免拉缸的產生具有重要的指導意義1 拉缸形成的機理 拉缸的機理，直觀地說，就是活塞或活塞環與缸套之間局部產生高溫使環與缸套產生高溫熔蝕粘附，活塞與缸套之間的油膜中斷是產生拉缸的主要原因，活塞與缸套之間的油膜一旦中斷，則兩種金屬就產生干磨擦，由于高速的相對運動產生的

3、高溫會超過金屬的熔點，引起活塞、活塞環與缸套表面產生熔蝕粘附，活塞繼續運動時，兩表面熔蝕粘附點又被扯斷，產生拉缸。 2 造成發動機拉缸的原因 2.1 超負荷 新機械或剛大修出廠的機械都存在一個合理的磨合期，磨合期內不能全速運轉，轉速不應大于標定轉速的80%，由于在磨合階段，各配合面最有利的工作表面和潤滑油膜還未形成，在這個階段就以大負荷工作，將造成過熱，局部產生高溫熔蝕粘附，形成拉缸。 2.2 活塞與缸套配合間隙過小 從密封角度來講，活塞與缸套配合間隙越小越好，但如果太小，發動機工作時，產生的高溫使活塞、活塞環、缸套受熱膨脹。由于活塞的膨脹系數比活塞環、缸套的膨脹系數大，因此，活塞受熱后的膨脹

4、量比缸套膨脹量大，這樣將破壞活塞與缸套之間的油膜，導致拉缸。 2.3 發動機溫度過高 由于發動機溫度過高，使活塞膨脹量過大，消除配合間隙，造成拉缸。造成發動機溫度過高的原因主要有： (1) 冷卻系漏水、缺水 氣缸墊水道口沖壞或濕式缸套突出量不符合要求，以及濕式缸套水封圈老化或損壞都會造成冷卻水內泄漏。散熱器遭腐蝕或破損，水管老化碰壞，水管接頭松動，水泵水封損壞等，都會引起冷卻水外泄漏。另外，氣缸蓋本身鑄造有缺陷或使用不當產生裂紋也會造成漏水，從而引起發動機溫度過高。 (2) 長時間超負荷使用 發動機長時間超負荷使用，將使發動機產生大量的熱能，冷卻系統不能散去多余的熱量，這樣就維持不了發動機正常

5、的工作溫度，使發動機產生高溫。 (3) 節溫器失效，無大循環 節溫器的作用是控制水溫在一定范圍，在水溫較低時，節溫器關閉，水從節溫器直接經旁通管流回冷卻水泵，不經過散熱器，這就是冷卻水的小循環過程。當水溫升到一定程度時，節溫器自動打開，水經過散熱器循環，這就是冷卻水的大循環，如果節溫器失效，冷卻水無大循環，發動機工作產生多余的熱量就不能通過散熱器散發出去，使發動機溫度過高。 (4) 冷卻水泵損壞強制冷卻水在發動機水套和散熱器之間進行循環靠的是冷卻水泵，冷卻水泵損壞，冷卻水就不能循環，發動機產生產熱量也就沒法通過水循環散發到大氣中去，從而引起發動機溫度過高。 (5) 水道或散熱器通風受堵 水道受

6、阻必將造成循環水量減少，從而影響到散熱量。散熱器通風受堵，影響散熱器的有效散熱面積，有效散熱面積減少，散熱能力就下降，這些原因都會使發動機的多余熱量得不到散發而造成發動機溫度過高。 (6) 噴油提前角過小或噴油量過大 噴油提前角過小，使燃燒推后，造成補充燃燒量增加，噴油量過大使燃燒產生的熱量增加，這兩種情況都會使發動機溫度過高。 3 機油不足 不按規定檢查機油量，或在工作過程因機油管松動造成機油外漏，均可造成潤滑油膜中斷，活塞與缸套表面失油，造成嚴重磨損，發生拉缸、燒連桿軸承等嚴重事故，特別是工作過程因機油外漏，沒有及時發現，將產生嚴重后果。造成活塞與缸套表面機油供油不足的原因還有以下幾個主要

7、方面： 3.1 潤滑油路堵塞 當潤滑系長期使用，沒有定期進行清洗時，過多的雜質會堵塞油路或機油濾清器，使循環油量不足。 3.2 活塞環與活塞邊緣刮油能力太強 刮油能力太強會把潤滑油刮掉，造成潤滑油不足。 3.3 機油變質發動機潤滑油變質造成活塞與缸套之間的潤滑條件惡化，磨損加快，引起拉缸，造成潤滑油變質的主要原因有：(1) 冷卻水、燃油因泄漏進入下曲軸箱 (2) 塵埃過多混入下曲軸箱4 活塞銷與活塞裝配過緊活塞銷與活塞裝配過緊，使活塞產生變形，形成反橢圓，改變了正常的標準間隙，形成局部間隙過小破壞油膜，引起干磨擦過熱拉缸。5 修理裝配錯誤 修理裝配錯誤時，漏裝活塞銷卡環或未完全裝入槽內，發動機

8、在工作時活塞銷竄出刮傷缸套造成拉缸。安裝時清潔工作差，把金屬屑或硬物碎粒帶進缸里，也會引起拉缸。另外，活塞環裝錯、裝反、漏裝均可造成拉缸。活塞環有油環和氣環之分，油環主要是用來刮油，并使?jié)櫥途鶆蚍植荚诟滋變?nèi)表面上，改善缸套潤滑條件。氣環主要是保證活塞與缸套的密封，氣環一般又設置一、二、三道。根據工作條件以及承受壓力的不同，各道氣環在材料選用和結構設計方面有所不同，如果把活塞環裝錯、裝反或漏裝，均有可能造成密封不嚴或是沒有刮油作用，使缸套內表面潤滑條件惡化，造成缺油引起拉缸。 6 活塞環折斷 活塞環折斷卡死在環槽內，將使環失去彈性，加速缸套的磨損，引起拉缸。造成環折斷卡死的原因主要是環的開口間

9、隙過小、活塞在缸套中偏斜、燃燒不良，使發動機經常處于爆燃的狀況下運行。爆燃的高壓振動沖擊力超過了環的材料的抗沖擊強度，引起活塞環折斷。其折斷一般發生在第一道環，其次是第二道環。活塞環卡死是由于燃燒時生成的積炭，尤其是竄機油或塵土、磨屑等堵塞在活塞環與環槽之間，使活塞環卡死在環槽中所致。 此外，活塞、活塞環、缸套的質量及材料對拉缸也有一定的影響。 7 防止發動機拉缸的措施 7.1 司機操作必須嚴格遵守操作規程起動前，必須按規定檢查潤滑油，冷卻水是否符合規定，不足時需補足，檢查判斷潤滑油是否變質，潤滑油呈乳白色一般是進水所致，潤滑油變稀且有柴油味說明進了柴油，潤滑油變質應查明原因，排除后更換潤滑油

10、。要嚴格執行保養制度，按期進行例保、一級保養和二級保養。 不超負荷作業。起動后不猛加油門，尤其在寒冷的冬季，需經低速運轉幾分鐘后再起步運行。 遇有異常情況，如機油壓力低，水溫高，有異常響聲等，應及時排除，堅持不帶病作業。 7.2 在修理裝配方面，必須嚴格遵守技術標準和工藝要求 對換新用的零配件必須逐個進行檢測，把不符合標準的零配件剔除出去，不能認為新產品就是合格的產品。 安裝缸套時，缸套要放平，壓力要作用在缸套正中，且慢慢加壓，勿用沖擊力。安裝完后進行檢測，檢測缸套與活塞裝配間隙是否符合規定的標準間隙。同樣，檢測活塞環與槽的邊隙、背隙、活塞環的端隙以及活塞銷與活座孔的裝配間隙是否符合規范要求，

11、檢查活塞環是否有裂縫以及環的彈力是否符合要求，裝好環后能自由活動，不得有卡滯現象?；钊h(huán)三隙（端隙、背隙、側隙）的檢查是組裝活塞連桿組的一個重點，特別是端隙大小尤為重要，稍有不慎就可能造成拉缸，環端隙的檢查要按工藝要求進行，檢查活塞環端隙的工藝要求是：將環放入缸套中，用活塞頂部將活塞環頂入缸套里，把環頂?shù)皆诨钊谐虄?nèi)最小直徑處測量，這樣測量的數據才準確。認真檢查活塞、連桿與曲軸安裝位置偏差情況、要求校正到符合技術規范標準。 在市場上購買的活塞，難辨優劣，在裝配前最好進行消除應力處理，即將活塞放在60-80度的機油中加溫6小時，以消除應力，使活塞穩定后再裝配使用。 安裝活塞環時各道環必須裝準位置

12、，不能裝錯、裝反、漏裝，注意方向性，扭曲環內圓切口朝上，外圓切口朝下，有標記的一面朝上，同時，在裝入缸套時必須清潔和加一定的潤滑油，各道環口應按規定錯開，第一道環開口與曲軸軸線成45度，余下各道的開口按90度、180度一一錯開。 裝配完畢，必須經15小時左右的熱磨合，試車磨合時，應先低速運轉，然后才中速運轉，應注意響聲、機油壓力、水溫等情況，在確定無異常后，再投入生產。 總之，只要我們掌握造成拉缸的原因，科學地管理和正確使用，嚴格遵守操作規程，落實預防措施，就一定能減少甚至避免拉缸的發生。附件2：外文原文Discussion on the engine cylinder scoring 摘要簡

13、述發動機拉缸的機理，分析造成發動機拉缸的原因，并提出了防止拉缸的措施。 Abstract this paper pull-cylinder engine mechanism, analyze the reasons for the engine cylinder scoring and proposed measures to prevent the pull cylinder. 關鍵詞發動機 拉缸 預防措施 Key words pull-cylinder engine of preventive measures 發動機在工作過程中常常遇到發動機拉缸現象，所謂拉缸，就是發動機的活塞環或活塞與

14、缸套的工作表面出現拉傷、拉毛、拉成溝槽的現象。 In the course of the engine is often encountered in the engine cylinder scoring phenomenon, the so-called pull-cylinder, that is, engine piston rings or piston and cylinder liner surface of the work injury, nap, pull into the groove phenomenon. 拉缸具有相當?shù)奈：Γ讜r缸套的的磨損率很高，最高可達正常的幾

15、百倍，使活塞、活塞環及缸套的壽命大為降低，使活塞與缸套咬死，造成發動機損壞。 Pull cylinder considerable harm, pull the cylinder when the cylinder liner wear rate is high, up to several hundred times the normal, so that the piston, piston ring and cylinder liner greatly reduced life expectancy, so that the piston and cylinder liner bite,

16、 resulting in engine damage. 因此，掌握拉缸形成的機理，認真分析造成拉缸的原因，研究預防措施，對避免拉缸的產生具有重要的指導意義 Therefore, the master cylinder pull forming mechanism, carefully analyze the reasons for pulling cylinder to study the preventive measures to avoid pull-cylinder produces an important guiding significance for 1拉缸形成的機理 1 T

17、he mechanism of the formation of a pull-cylinder 拉缸的機理，直觀地說，就是活塞或活塞環與缸套之間局部產生高溫使環與缸套產生高溫熔蝕粘附，活塞與缸套之間的油膜中斷是產生拉缸的主要原因，活塞與缸套之間的油膜一旦中斷，則兩種金屬就產生干磨擦，由于高速的相對運動產生的高溫會超過金屬的熔點，引起活塞、活塞環與缸套表面產生熔蝕粘附，活塞繼續運動時，兩表面熔蝕粘附點又被扯斷，產生拉缸。 Pull cylinder mechanism, intuitively, this means between piston or piston ring and cyli

18、nder liner locally generated heat to produce high-temperature melting ring and cylinder liner erosion adhesion between the piston and cylinder liner oil film disruption is to generate the main reason for pulling cylinder , oil film between the piston and cylinder liner, once interrupted, then the tw

19、o metals to produce dry friction, high-speed relative motion due to the heat generated will exceed the melting point of metal, causing piston, piston ring and cylinder liner erosion surface of the melt adhesion, Pistons continue to exercise, the two adhesion points of the surface ablation was snappe

20、d, resulting in cylinder scoring. 2 造成發動機拉缸的原因 2 cylinder causing the engine pulling the reasons for 2.1超負荷 2.1 Overload 新機械或剛大修出廠的機械都存在一個合理的磨合期，磨合期內不能全速運轉，轉速不應大于標定轉速的80%，由于在磨合階段，各配合面最有利的工作表面和潤滑油膜還未形成，在這個階段就以大負荷工作，將造成過熱，局部產生高溫熔蝕粘附，形成拉缸。 New machinery or just overhaul the mechanical factory there a r

21、easonable run-in period, running-in period and can operate at full speed, speed should not exceed 80% of the speed calibration, since the run-in period, the mating surface of the most favorable working surface and lubricant film has not yet formed at this stage of large load of work, it will cause o

22、verheating and partial melting high-temperature corrosion resulting adhesion, the formation of pull-cylinder. 2.2活塞與缸套配合間隙過小 2.2 The gap with the piston and cylinder is too small 從密封角度來講，活塞與缸套配合間隙越小越好，但如果太小，發動機工作時，產生的高溫使活塞、活塞環、缸套受熱膨脹。 From the sealing point of view, the piston and cylinder with the

23、gap as small as possible, but if too small, engine work, the resulting heat to the piston, piston rings, cylinder liner thermal expansion. 由于活塞的膨脹系數比活塞環、缸套的膨脹系數大，因此，活塞受熱后的膨脹量比缸套膨脹量大，這樣將破壞活塞與缸套之間的油膜，導致拉缸。 As the piston expansion coefficient than the piston ring, cylinder liner expansion coefficient,

24、therefore, than the expansion of the piston cylinder after heat expansion of volume, which would undermine the oil film between the piston and cylinder liner, resulting in cylinder scoring. 2.3發動機溫度過高 2.3 engine temperature is too high 由于發動機溫度過高，使活塞膨脹量過大，消除配合間隙，造成拉缸。 As the engine temperature is too

25、 high, so that excessive expansion of the piston to eliminate with the gap, resulting in cylinder scoring. 造成發動機溫度過高的原因主要有： Causing the engine temperature is too high main reasons are: (1) 冷卻系漏水、缺水 (1) cooling system leaks, water shortages 氣缸墊水道口沖壞或濕式缸套突出量不符合要求，以及濕式缸套水封圈老化或損壞都會造成冷卻水內泄漏。 Cylinder Hea

26、d Gasket water crossings washed out or highlight the amount of wet cylinder liner does not meet the requirements, as well as wet-aging or damaged cylinder seal ring will result in leakage of cooling water. 散熱器遭腐蝕或破損，水管老化碰壞，水管接頭松動，水泵水封損壞等，都會引起冷卻水外泄漏。 Radiator has been corrosion or damage, aging of th

27、e pipe break something, plumbing joints loose, water pump seal damage and so on, would give rise to the cooling water that leaked. 另外，氣缸蓋本身鑄造有缺陷或使用不當產生裂紋也會造成漏水，從而引起發動機溫度過高。 In addition, the cylinder head casting itself is defective or improper use can also cause cracks leaking, causing the engine te

28、mperature is too high. (2) 長時間超負荷使用 (2) the use of long overload 發動機長時間超負荷使用，將使發動機產生大量的熱能，冷卻系統不能散去多余的熱量，這樣就維持不了發動機正常的工作溫度，使發動機產生高溫。 Overload the engine a long time to use, the engine will generate a lot of heat, cooling system can not disperse the excess heat, so that the engine can not maintain the

29、 normal operating temperature, so that the engine produces heat. (3)節溫器失效，無大循環 (3) The thermostat failed, no big loop 節溫器的作用是控制水溫在一定范圍，在水溫較低時，節溫器關閉，水從節溫器直接經旁通管流回冷卻水泵，不經過散熱器，這就是冷卻水的小循環過程。 The role of thermostat is to control the water temperature in a certain range, in the water temperature is low, t

30、he thermostat off, water from the thermostat directly through the bypass pipe flow back into the cooling water pump, not through the radiator, which is the cooling water-cycle process. 當水溫升到一定程度時，節溫器自動打開，水經過散熱器循環，這就是冷卻水的大循環，如果節溫器失效，冷卻水無大循環，發動機工作產生多余的熱量就不能通過散熱器散發出去，使發動機溫度過高。 When the water temperatur

31、e rose to a certain extent, the thermostat automatically open, the water circulating through the radiator, which is a large cycle of cooling water, if the thermostat fails, no big loop cooling water, the engine work of excess calories as heat can not be devices distributed out, the engine temperatur

32、e is too high. (4) 冷卻水泵損壞 (4) cooling water pump is damaged 強制冷卻水在發動機水套和散熱器之間進行循環靠的是冷卻水泵，冷卻水泵損壞，冷卻水就不能循環，發動機產生產熱量也就沒法通過水循環散發到大氣中去，從而引起發動機溫度過高。 Forced cooling water in the engine water jacket and circulating between the radiator depends on the cooling water pump, cooling water pump is damaged, the co

33、oling water is not circulating, the engine output also can not produce heat emitted to the atmosphere through the water cycle going, which led to the engine temperature too high. (5)水道或散熱器通風受堵 (5) watercourse or by blocking the ventilation radiator 水道受阻必將造成循環水量減少，從而影響到散熱量。 Watercourse blocked will i

34、nevitably lead to reduced water circulation, which affects the heat dissipation. 散熱器通風受堵，影響散熱器的有效散熱面積，有效散熱面積減少，散熱能力就下降，這些原因都會使發動機的多余熱量得不到散發而造成發動機溫度過高。 Cooler air by blocking, affecting the effective thermal radiator area, effective heat dissipation area of reduced ability to decrease heat dissipatio

35、n, which would make the engine caused by excess heat is not distributed the engine temperature is too high. (6) 噴油提前角過小或噴油量過大 (6) injector fuel injection advance angle is too small or too large 噴油提前角過小，使燃燒推后，造成補充燃燒量增加，噴油量過大使燃燒產生的熱量增加，這兩種情況都會使發動機溫度過高。 Fuel injection advance angle is too small, so tha

36、t combustion pushed back, resulting in increased complement combustion, fuel injection combustion heat generated by excessive increase in both cases will cause the engine temperature is too high. 3機油不足 3 oil shortage 不按規定檢查機油量，或在工作過程因機油管松動造成機油外漏，均可造成潤滑油膜中斷，活塞與缸套表面失油，造成嚴重磨損，發生拉缸、燒連桿軸承等嚴重事故，特別是工作過程因機油

37、外漏，沒有及時發現，將產生嚴重后果。 Do not check the oil quantity required, or in the work process due to loosening caused by oil leakage of oil pipes, can cause interruption of lubricating oil film, the surface loss of oil piston and cylinder, causing serious wear and tear, occurred pull cylinder, connecting rod be

38、arings and other serious incidents burning , especially in the work process due to oil leakage, failure to make timely discovery, will have serious consequences. 造成活塞與缸套表面機油供油不足的原因還有以下幾個主要方面： Caused by the surface of the piston and the cylinder fuel supply shortage of oil because there are several m

39、ain areas: 3.1 潤滑油路堵塞 3.1 Lubrication plug 當潤滑系長期使用，沒有定期進行清洗時，過多的雜質會堵塞油路或機油濾清器，使循環油量不足。 Lubrication System When the long-term use, there is no regular cleaning, excessive impurities will plug the oil line or oil filter, so that enough fuel cycles. 3.2 活塞環與活塞邊緣刮油能力太強 3.2 piston rings and piston scrap

40、ing the edge of the oil capacity is too strong 刮油能力太強會把潤滑油刮掉，造成潤滑油不足。 Lubricating oil capacity is too strong will scratch scratch, resulting in insufficient lubricant. 3.3機油變質 3.3 Oil metamorphic 發動機潤滑油變質造成活塞與缸套之間的潤滑條件惡化，磨損加快，引起拉缸，造成潤滑油變質的主要原因有： Degeneration caused by engine oil lubrication between

41、the piston and cylinder liner deterioration in the terms, accelerated wear and tear caused pull-cylinder, resulting in deterioration of the main reasons oil are: (1)冷卻水、燃油因泄漏進入下曲軸箱 (1) cooling water, fuel leaking into the next due to crankcase (2) 塵埃過多混入下曲軸箱 (2) mixed with too much dust under the cr

42、ankcase 4 活塞銷與活塞裝配過緊 4 piston pin and piston assembly of tight 活塞銷與活塞裝配過緊，使活塞產生變形，形成反橢圓，改變了正常的標準間隙，形成局部間隙過小破壞油膜，引起干磨擦過熱拉缸。 Piston pin and piston assembly too tight, so that the piston deformation, the formation of anti-oval, changing the normal standards of space, form a partial destruction of oil f

43、ilm clearance is too small, causing dry friction pull cylinder overheating. 5修理裝配錯誤 5 repair assembly error 修理裝配錯誤時，漏裝活塞銷卡環或未完全裝入槽內，發動機在工作時活塞銷竄出刮傷缸套造成拉缸。 Repair assembly errors, and missed mounted piston pin snap ring or fully loaded tank, the engine piston pin sprang at work scratching caused by pu

44、lling cylinder liner. 安裝時清潔工作差，把金屬屑或硬物碎粒帶進缸里，也會引起拉缸。 Installation, cleaning work is poor, the hard objects of metal scrap or crushed into the tank, can cause pulling cylinder. 另外，活塞環裝錯、裝反、漏裝均可造成拉缸。 In addition, the piston rings installed wrong, install anti-, leakage may be caused by pulling cylinde

45、r installed. 活塞環有油環和氣環之分，油環主要是用來刮油，并使?jié)櫥途鶆蚍植荚诟滋變?nèi)表面上，改善缸套潤滑條件。 Of oil and gas piston ring of the sub-ring, oil ring is mainly used to scrape oil, lubricants and to evenly distributed in the inner surface of the cylinder to improve the conditions for cylinder lubrication. 氣環主要是保證活塞與缸套的密封，氣環一般又設置一、二、三道

46、。 Gas ring main is to ensure that the sealing piston and cylinder, gas ring in general has set up one, two, three. 根據工作條件以及承受壓力的不同，各道氣環在材料選用和結構設計方面有所不同，如果把活塞環裝錯、裝反或漏裝，均有可能造成密封不嚴或是沒有刮油作用，使缸套內表面潤滑條件惡化，造成缺油引起拉缸。 According to the working conditions as well as the pressure difference, the Tao gas ring in

47、 the material selection and structural design is different, if the piston rings installed wrong, or omitted to install anti-loaded, are likely to result in Mifengbuyan or no role in the oil scraper , so that the inner surface of cylinder liner lubrication condition deteriorated, resulting in short o

48、f oil caused by pull-cylinder. 6 活塞環折斷 6 piston ring broken 活塞環折斷卡死在環槽內，將使環失去彈性，加速缸套的磨損，引起拉缸。 Broken piston ring stuck in the ring tank, will ring to lose flexibility, speed up the cylinder liner wear and tear, causing pulling cylinder. 造成環折斷卡死的原因主要是環的開口間隙過小、活塞在缸套中偏斜、燃燒不良，使發動機經常處于爆燃的狀況下運行。 Caused by

49、 broken ring stuck due mainly to ring the opening gap is too small, the deflection piston in the cylinder, burning bad, so often in the engine running under deflagration conditions. 爆燃的高壓振動沖擊力超過了環的材料的抗沖擊強度，引起活塞環折斷。 Deflagration of the high-pressure vibrating ring impact than the material impact stre

50、ngth, caused by broken piston rings. 其折斷一般發生在第一道環，其次是第二道環。 Its breaking generally occurs in the first ring, followed by the second ring. 活塞環卡死是由于燃燒時生成的積炭，尤其是竄機油或塵土、磨屑等堵塞在活塞環與環槽之間，使活塞環卡死在環槽中所致。 Stuck piston ring is due to combustion-generated carbon deposition, particularly in channeling oil or dust,

51、 debris and other plug in between the piston and ring groove, so that piston rings stuck in the ring slot due. 此外，活塞、活塞環、缸套的質量及材料對拉缸也有一定的影響。 In addition, piston, piston rings, cylinder liner quality and materials on the pull-cylinder also has a certain impact. 7 防止發動機拉缸的措施 7 of measures to prevent t

52、he engine cylinder scoring 7.1 司機操作必須嚴格遵守操作規程 7.1 and drivers to strictly observe the operational procedures 起動前，必須按規定檢查潤滑油，冷卻水是否符合規定，不足時需補足，檢查判斷潤滑油是否變質，潤滑油呈乳白色一般是進水所致，潤滑油變稀且有柴油味說明進了柴油，潤滑油變質應查明原因，排除后更換潤滑油。 Starting before they are required inspection of lubricating oil, cooling water to check for co

53、mpliance, required to make up for insufficient check to determine whether the deterioration oil, lubricating oil is milky white water is generally caused by thinning and lubricating oil shows a diesel smell into the diesel oil, lubricating oil deterioration causes should be identified, removed, repl

54、ace the oil. 要嚴格執行保養制度，按期進行例保、一級保養和二級保養。 To strictly enforce the maintenance of the system, scheduled for cases of insurance, maintenance and a maintenance 2. 不超負荷作業。 Do not overload operation. 起動后不猛加油門，尤其在寒冷的冬季，需經低速運轉幾分鐘后再起步運行。 Meng did not start after refueling door, especially in the cold winter,

55、 subject to a few minutes and then started to run low-speed operation. 遇有異常情況，如機油壓力低，水溫高，有異常響聲等，應及時排除，堅持不帶病作業。 The event of unusual circumstances, such as low oil pressure, water temperature high, abnormal noise, etc., should be promptly removed, insisted on not sick job. 7.2 在修理裝配方面，必須嚴格遵守技術標準和工藝要求

56、 7.2 In the repair of assembly, it should be strict compliance with technical standards and technological requirements 對換新用的零配件必須逐個進行檢測，把不符合標準的零配件剔除出去，不能認為新產品就是合格的產品。 Spare parts for new ones to be used to detect one by one, to remove non-compliant spare parts to go out and can not believe that the

57、new product is qualified product. 安裝缸套時，缸套要放平，壓力要作用在缸套正中，且慢慢加壓，勿用沖擊力。 Install cylinder, the cylinder should be flat, the pressure to the role of the middle of the cylinder, and slowly pressurized, do not use impact. 安裝完后進行檢測，檢測缸套與活塞裝配間隙是否符合規定的標準間隙。 After you install, testing, testing whether the cyl

58、inder and piston assembly clearance gap meet the required standards. 同樣，檢測活塞環與槽的邊隙、背隙、活塞環的端隙以及活塞銷與活座孔的裝配間隙是否符合規范要求，檢查活塞環是否有裂縫以及環的彈力是否符合要求，裝好環后能自由活動，不得有卡滯現象。 Similarly, the detection of piston ring and groove side clearance, backlash, piston ring end gap and piston pin hole with live seat assembly cl

59、earance compliance with regulatory requirements, check whether there are cracks as well as the piston ring elastic compliance requirements, install a good Central, can be freely, without catching the phenomenon. 活塞環三隙（端隙、背隙、側隙）的檢查是組裝活塞連桿組的一個重點，特別是端隙大小尤為重要，稍有不慎就可能造成拉缸，環端隙的檢查要按工藝要求進行，檢查活塞環端隙的工藝要求是：將環放

60、入缸套中，用活塞頂部將活塞環頂入缸套里，把環頂?shù)皆诨钊谐虄?nèi)最小直徑處測量，這樣測量的數據才準確。 Piston Ring Gap 3 (terminal gaps, backlash, backlash) in check is the piston rod assembly of a focus group, in particular the end-gap size is particularly important at the slightest mistake could result in pull-cylinder, ring end gap of the inspectio

61、n should carried out according to process requirements, check the piston ring end gap of the process requirements are: the ring into the cylinder, the piston ring with the piston at the top of the roof into the cylinder where the top ring to the piston stroke measured at the smallest diameter, so th

62、at measurement data are correct. 認真檢查活塞、連桿與曲軸安裝位置偏差情況、要求校正到符合技術規范標準。 Carefully check the piston, connecting rod and crankshaft installation position deviation, demand technical specifications that meet standards for calibration. 在市場上購買的活塞，難辨優劣，在裝配前最好進行消除應力處理，即將活塞放在60-80度的機油中加溫6小時，以消除應力，使活塞穩定后再裝配使用。

63、In the market to buy the piston, is hard to determine strengths and weaknesses, in the best pre-assembled to eliminate the stress treatment, about 60-80 degrees on the piston heating oil in 6 hours, in order to eliminate the stress, so that the piston assembly and stability before use. 安裝活塞環時各道環必須裝準

64、位置，不能裝錯、裝反、漏裝，注意方向性，扭曲環內圓切口朝上，外圓切口朝下，有標記的一面朝上，同時，在裝入缸套時必須清潔和加一定的潤滑油，各道環口應按規定錯開，第一道環開口與曲軸軸線成45度，余下各道的開口按90度、180度一一錯開。 When installing the piston rings must be installed with a position where the Tao can not be installed wrong, loaded trans, drain installation, pay attention to directions, twist ring round incision upward, cylindrical cut down, marked side facing up, at the same time, in the loaded cylinder m